1 # Copyright (C) 2008-2010 Andre Noll <maan@tuebingen.mpg.de>
3 # Licensed under the GPL v2. For licencing details see COPYING.
7 purpose "the dyadic snapshot scheduler
9 dss creates hardlink-based snapshots of a given directory on a remote
10 or local host using rsync's link-dest feature.
13 #########################
14 section "General options"
15 #########################
17 option "config-file" c
18 #~~~~~~~~~~~~~~~~~~~~~
19 "(default='~/.dssrc')"
20 string typestr="filename"
23 Options may be given at the command line or in the
24 configuration file. As usual, if an option is given both at
25 the command line and in the configuration file, the command
26 line option takes precedence.
28 However, there is an important exception to this rule:
29 If the --run option was given (see below) then dss honors
30 SIGHUP and re-reads its configuration file whenever it
31 receives this signal. In this case the options in the config
32 file override any options that were previously given at the
33 command line. This allows to change the configuration of a
34 running dss process on the fly by sending SIGHUP.
39 "Run as background daemon"
43 Note that dss refuses to start in daemon mode if no logfile
44 was specified. This option is mostly useful in conjunction
45 with the -R option described below.
47 Note that it is not possible to change whether dss runs as
48 background daemon by sending SIGHUP.
53 "Only print what would be done"
56 This flag does not make sense for all commands. The run
57 command refuses to start if this option was given. The ls
58 command silently ignores this flag.
72 Lower values mean more verbose logging.
77 "Logfile for the dss daemon process"
78 string typestr="filename"
81 This option is only honored if both --run and --daemon are
82 given. Otherwise it is silently ignored and log output is
93 dss supports a couple of commands each of which corresponds
94 to a different command line option. Exactly one of these
95 options must be given.
100 groupoption "create" C
101 #~~~~~~~~~~~~~~~~~~~~~
102 "Create a new snapshot"
105 Execute the rsync command to create a new snapshot. Note that
106 this command does not care about free disk space.
109 groupoption "prune" P
110 #~~~~~~~~~~~~~~~~~~~~
111 "Remove redundant and outdated snapshots"
114 A snapshot is considered outdated if its interval number
115 is greater or equal than the specified number of unit
116 intervals. See the \"Intervals\" section below for the precise
117 definition of these terms.
119 A snapshot is said to be redundant if it belongs to an
120 interval that already contains more than the desired number
123 The prune command gets rid of both outdated and redundant
129 "Print a list of all snapshots"
132 The list will contain all snapshots no matter of their state,
133 i. e. incomplete snapshots and snapshots being deleted will
139 "Start creating and pruning snapshots"
142 This is the main mode of operation. Snapshots will be created
143 in an endless loop as needed and pruned automatically. The loop
144 only terminates on fatal errors or if a terminating signal was
145 received. See also the --exit-hook option.
150 "Kill a running dss process"
153 This sends SIGTERM to the dss process that corresponds to the
154 given config file. If --dry-run is given, the PID of the dss
155 process is written to stdout, but no signal is sent.
158 groupoption "reload" -
159 #~~~~~~~~~~~~~~~~~~~~~
160 "force a running dss process to reload its config file"
163 This differs from --kill only in that SIGHUP rather than SIGTERM
164 is sent to the dss process.
167 ###############################
168 section "Rsync-related options"
169 ###############################
171 option "remote-host" H
172 #~~~~~~~~~~~~~~~~~~~~~
174 string typestr="hostname"
178 If this option is given and its value differs from the local
179 host, then rsync uses ssh. Make sure there is no password
180 needed for the ssh connection. To achieve that, use public key
181 authentication for ssh and, if needed, set the remote user name
182 by using the --remote-user option.
185 option "remote-user" U
186 #~~~~~~~~~~~~~~~~~~~~~
187 "Remote user name (default: current user)"
188 string typestr="username"
191 Set this if the user running dss is different from the
192 user at the remote host when using ssh.
195 option "source-dir" -
196 #~~~~~~~~~~~~~~~~~~~~
198 string typestr="dirname"
201 The directory on the remote host from which snapshots are
202 taken. Of course, the user specified as --remote-user must
203 have read access to this directory.
209 string typestr="dirname"
212 The destination directory on the local host where snapshots
213 will be written. This must be writable by the user who runs
219 "Do not try to resume from previous runs"
222 Starting from version 0.1.4, dss tries to resume from a
223 previously cancelled dss instance by default. It does so by
224 looking at the status of the most recently created snapshot. If
225 this snapshot status is incomplete, its directory is reused
226 as the destination directory for a subsequent rsync run.
228 The --no-resume option deactivates this feature so that a new
229 directory is always used as the rsync destination directory.
232 option "rsync-option" O
233 #~~~~~~~~~~~~~~~~~~~~~~
234 "Further rsync options"
235 string typestr="option"
239 This option may be given multiple times. The given argument is
240 passed verbatim to the rsync command. Note that in order to use
241 rsync options that require an argument, you have to specify the
242 option and its argument as separate --rsync-options, like this:
244 --rsync-option --exclude --rsync-option /proc
247 option "max-rsync-errors" -
248 "Terminate after this many rsync failures"
253 Only relevant when operating in --run mode (see above). If
254 the rsync process exits with a fatal error, dss restarts
255 the command in the hope that the problem is transient
256 and subsequent rsync runs succeed. After the given number
257 of consecutive rsync error exits, however, dss gives up,
258 executes the exit hook and terminates. Set this to zero if
259 dss should exit immediately on the first rsync error.
261 The only non-fatal error is when rsync exits with code 24. This
262 indicates a partial transfer due to vanished source files
263 and happens frequently when snapshotting a directory which
264 is concurrently being modified.
271 option "unit-interval" u
272 #~~~~~~~~~~~~~~~~~~~~~~~
273 "The duration of a unit interval"
278 dss snapshot aging is implemented in terms of intervals. There
279 are two command line options related to intervals: the
280 duration u of a \"unit\" interval and the number n of those
283 dss removes any snapshots older than n times u and tries to
284 keep 2^(n - k - 1) snapshots in interval k, where the interval
285 number k counts from zero, zero being the most recent unit
288 In other words, the oldest snapshot will at most be u * n days
289 (= 20 days if default values are used) old. Moreover, there
290 are at most 2^n - 1 snapshots in total (i. e. 31 by default).
291 Observe that you have to create at least 2^(n - 1) snapshots
292 each interval for this to work out because that is the number
293 of snapshots in interval zero.
296 option "num-intervals" n
297 #~~~~~~~~~~~~~~~~~~~~~~~
298 "The number of unit intervals"
307 option "pre-create-hook" r
308 #~~~~~~~~~~~~~~~~~~~~~~~~~~
309 "Executed before snapshot creation"
310 string typestr="command"
314 Execute this command before trying to create a new snapshot.
315 If this command returns with a non-zero exit status, no
316 snapshot is being created and the operation is retried later.
318 For example, one might want to execute a script that checks
319 whether all snapshot-related file systems are properly mounted.
321 Another possible application of this is to return non-zero
322 during office hours in order to not slow down the file systems
326 option "post-create-hook" o
327 #~~~~~~~~~~~~~~~~~~~~~~~~~~
328 "Executed after snapshot creation"
329 string typestr="command"
333 Execute this after a snapshot has successfully been
334 created. The full path of the newly created snapshot is
335 passed to the hook as the first argument. The exit code of
336 this hook is ignored.
338 For instance this hook can be used to count the number of
339 files per user and/or the disk usage patterns in order to
340 store them in a database for further analysis.
343 option "pre-remove-hook" -
344 #~~~~~~~~~~~~~~~~~~~~~~~~~~
345 "Executed before snapshot removal"
346 string typestr="command"
350 Execute this command before removing a snapshot. The full
351 path to the snapshot about to be deleted is passed to the
352 command as the first argument. If the command returns with
353 a non-zero exit status, no snapshot is being removed and the
354 operation is retried later.
356 For example, one might want to execute a script that checks
357 whether the snapshot to be deleted is currently used by
358 another process, e.g. by a tape-based backup system that runs
361 Another possible application of this is to record disk-usage
362 patterns before and after snapshot removal.
365 option "post-remove-hook" -
366 #~~~~~~~~~~~~~~~~~~~~~~~~~~
367 "Executed after snapshot removal"
368 string typestr="command"
372 Execute this after a snapshot has successfully been removed. As
373 for the pre-remove hook, the full path of the removed snapshot
374 is passed to the hook as the first argument. The exit code
375 of this hook is ignored.
380 "Executed if run command exits"
381 string typestr="command"
385 This hook is only used if the --run command was given which
386 instructs dss to run in an endless loop. The exit-hook gets
387 executed whenever this endless loop terminates. The reason
388 for terminating the loop is passed as the first argument.
390 One possible application for this hook is to send email to the
391 system administrator to let her know that no more snapshots
392 are going to be created.
395 ###############################
396 section "Disk space monitoring"
397 ###############################
399 option "min-free-mb" m
400 #~~~~~~~~~~~~~~~~~~~~~
401 "Minimal amount of free disk space"
402 int typestr="megabytes"
406 If disk space on the file system containing the destination
407 directory gets low, \"dss --run\" will suspend the currently
408 running rsync process and will start to remove snapshots in
409 order to free disk space. This option specifies the minimal
410 amount of free disk space. If less than the given number of
411 megabytes is available, snapshots are being deleted. See also
412 the --min_free_percent and the min-free-percent-inodes options.
414 A value of zero deactivates this check.
417 option "min-free-percent" p
418 #~~~~~~~~~~~~~~~~~~~~~~~~~~
419 "Minimal percent of free disk space"
420 int typestr="percent"
424 See --min-free-mb. Note that it is not recommended to set both
425 --min-free-mb and --min-free-percent to zero as this will
426 cause your file system to fill up quickly.
428 option "min-free-percent-inodes" i
429 #~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
430 "Minimal percent of free inodes"
431 int typestr="percent"
435 Specify the minimum amount of free inodes on the file system
436 containing the destination dir. If less than that many inodes
437 are free, snapshot removal kicks in just as in case of low
440 Note that not every file system supports the concept of inodes.
441 Moreover it is not possible to reliably detect whether this is
442 the case. Therefore this feature is disabled by default. It's
443 safe to enable it for ext2/ext3/ext4 file systems on linux
446 A value of zero (the default) deactivates this check.
449 option "keep-redundant" k
450 #~~~~~~~~~~~~~~~~~~~~~~~~
451 "Prune by disk space only"
454 If this flag is not given dss removes redundant and outdated
455 snapshots automatically.
457 Otherwise, this feature is deactivated so that snapshots are
458 only being removed in case disk space or number of free inodes
459 becomes low. Use this flag if the file system containing the
460 destination directory is used for snapshots only.
463 option "min-complete" -
464 #~~~~~~~~~~~~~~~~~~~~~~
465 "Minimal number of complete snapshots to keep"
470 This option is only relevant if snapshots must be deleted
471 because disk space gets low.
473 dss refuses to remove old snapshots if there are fewer complete
474 snapshots left than the given number. The default value of one
475 guarantees that at least one complete snapshot is available
478 If only <num> complete snapshot are left, and there is not
479 enough disk space available for another snapshot, the program
480 terminates with a \"No space left on device\" error.